system: Linux

language: English, Chinese, Hungarian, other optional

Operation Mode:

User interface, controller, mobile app, network

CPU:

Novatek NT98323

Internal Memory:

DDR3 4GBIT Flash 128M Nand

Power consumption:

Bare device: ≤4w

Fully functional: ≤60w
Applicable vehicles (power supply):
8~36V voltage vehicle can run, optional additional UPS (battery) support, different capacities can be selected 1-3 hours

Voltage input:
1.The input voltage is +8V to +36V. If the voltage is lower than 8V or higher than 36V for a long time, the device will automatically shut down and enter protection mode.
2. Pure step-down power supply, the system is divided into two power supplies (camera and system power supplies are independent)

CAME_12V X 8:
The total current is 5A, which is a 1A interface connected to the AHD camera. You can control the switch and power of the camera as needed. The system can control the power of the camera and monitor independently, which is convenient for shutting down unnecessary cameras and monitors after a delayed shutdown.

12V output:

The output voltage is 12V (+/- 0.2V) and the maximum current is 3A.

5V output:

The output voltage is 5V (+/- 0.2V) and the maximum current is 1A.

Preview function:Supports 8-screen splicing for preview, which can be event-triggered to switch between full-screen and splicing display.

Frame rate1080P: maximum 120 frames/sec 720P: 240 frames/sec NTSC: 240 frames/sec Single channel maximum: 30 frames/sec

ResolutionSupports 1080P, 720P, and D1 encoding formats.

Picture quality level1 to 7 levels can be configured, where level 1 is the best and level 7 is the lowest.

Code rate (Bitrate) OptionsD1: 512, 768, 1024 (three levels optional) 720P: 1024, 2048, 4096 (three levels optional) 1080P: 2048, 4096, 6144 (three levels optional)

5x7F*2.7V:

1. Power on and charge, and it will be fully charged in 3 minutes. Even if the external power fails, the system can still operate for 10 seconds and continue to complete data saving and shutdown.
2. To ensure that the device does not restart when the input power is unstable.
3. Built-in UPS polymer battery optional (1-3 hours), built-in interface and fixed position as standard configuration

Car Key (ACC) Signal：

≤6VThe car key is off

≥7VThe car key is on

Storage method

Three memory card slots: two SD cards, one TF card, single card supports a maximum capacity of 512G, and an SSD slot is reserved for optional addition

Storage method:

1. Support SD card, TF card loop recording, loop deletion (the oldest video will be deleted)

2. Support SD card loop recording, TF card mirroring, and supplementary recording.

Video Detection:

Search by recording time, recording type, recording storage device, etc.

File Format/System:

H.265/FAT32

Video Mode:

Recording is enabled by default and supports manual recording, alarm recording, timed recording, mirror recording, etc.

Video Search:

Search by recording time, recording type, recording storage, etc.)

Video playback:

Supports local playback, can play up to 4 channels simultaneously, and analyze vehicle information in the file at the same time.

Video playback:

Support fast forward, fast rewind, play, pause control, support 2x, 4x, 8x, 16x fast forward or rewind, support time selection playback control

RS232/458:

2xRS232, 1xRS485

Can connect alcohol detection sensor, tire pressure detection sensor, LED control panel and other peripherals through preset interface

USB:

Usb2.0, the front USB shell is used for data export and upgrade

1. Wire:

1-wire support for I Button

Support CMS platform for download/playback and history.

The stored video is in an encrypted format and can be played through the MDVRplayer software.

Built-in global positioning system (GPS) module and antenna, which can realize real-time positioning, speed detection, GPS time synchronization, and report location information to the CMS platform in real time, facilitating fleet management

Compatible with 3/4/5G:

Optional modules

EVDO/TD-SCDMA/WCDMA/TDD-LTE/FDD-LTE, etc.

Optional built-in WIFI module and antenna

WiFi makes MDVR menu settings simple, eliminating the need for a remote control Support wireless video download

802.11b/g/n/ 2.4G/5.8G optional

RJ45 Network:

1 × RJ45 for expansion connection of IPC camera

USB interface:

2 USB 2.0 ports, front panel for downloading video files and upgrading firmware; rear panel for backing up records and connecting to firebox

6*I/O Alarm output（12V/GND）
Can receive level signals such as turn signal to trigger alarm

Monitoring function:

You can use the CMS platform to initiate monitoring broadcasts

Automatically correcting and doing not limit the installation direction of the equipment